Influence of surface roughness of universal shade resin composites on color adjustment potential.

This study aimed to determine the influence of surface roughness of the color adjustment potential restoration of universal resin composites. A structural colored resin composite (Omnichroma, OC) and a pigment-employed universal shade resin composite (Beautifil Unishade, BU) were used. Each resin composite was placed in a cavity to determine its ability to match the color of artificial teeth. The surface of the resin composites was polished with #800- or #2000-grit SiC paper before performing color measurements. One-way analysis of variance and Tukey post hoc tests were performed (α=0.05). The color difference (ΔE*ab) ranged from 2.5-3.9 for OC and 1.8-8.7 for BU. OC has a more stable color adjustment than BU. The color adjustment potential of universal resin composites was affected by the surface roughness of the restorations.

Evaluation of the effect of a glass ionomer cement containing fluoro-zinc-silicate glass on dentin remineralization using the ultrasonic pulse-echo method.

The purpose of this study was to investigate the protective effect of a glass ionomer cement (GIC) consisting of fluoro-zinc-silicate glass on the demineralization of bovine dentin using the ultrasonic pulse-echo method. The findings were compared with those obtained using a conventional GIC. Slabs of dentin from bovine teeth were sliced, shaped into a rectangular form, and immersed in 0.5 M ethylenediaminetetraacetic acid solution at 25ºC for 6 days, followed by storage in distilled water for 3 days. After demineralization, they were immersed in artificial saliva with and without the GIC specimens. The propagation times of the longitudinal ultrasonic waves in the samples were measured. The ultrasonic velocities of the fluoro-zinc-silicate glass-containing GICs were significantly increased 2-3 days after the start of the experiment and showed an upward trend thereafter. These findings indicate that the GICs containing fluoro-zinc-silicate glass might exhibit the potential to promote remineralization in the dentin.

Bonding ability of resin cements to different types of CAD/CAM composite blocks.

This study investigated the bonding performance of two different types of resin cements to computer-aided design/computer-aided manufacturing (CAD/CAM) composite blocks based on the shear bond strength (SBS) test. A silane-containing self-adhesive resin cement (Panavia SA Cement Universal) and resin luting cement (Block HC Cem) with a primer, were used. Specimens were fabricated from three different types of CAD/CAM composite blocks, and their surfaces were blasted with alumina. Resin cements were bonded to the specimens, and their SBSs were measured after 15 min, 24 h, and after being subjected to thermal cycling for 10,000 and 30,000 cycles. Three-way ANOVA for bond strength revealed that CAD/CAM composite block, resin cement and storage time significantly influenced the SBS values, and the three-way interactions between the evaluated factors, and all the interactions were significant. It was concluded that the bonding performance of resin cements to CAD/CAM composite blocks were material and storage period dependent.

Effect of ion-releasing filler-containing gel application on dentin remineralization using optical coherent tomography.

PURPOSE: To examine the effects of an ion-releasing filler-containing gel on the remineralization of dentin using optical coherence tomography (OCT). METHODS: Dentin slabs of bovine teeth were sliced and shaped into a rectangular form. Specimens were treated with undersaturated 0.1 M lactic acid buffer solution (pH 4.75) for 10 minutes and then placed in artificial saliva (pH 7.0). This procedure was repeated three times a day for 28 days. The dentin remineralization effects of a fluoride/S-PRG filler-containing gel (PRG) and a 38% SDF solution (SDF) on dentin slabs of bovine teeth were compared. After treatment, the dentin slabs were immersed in a 0.1 M lactic acid buffer solution and then placed in artificial saliva. This procedure was repeated three times a day for 28 days. OCT imaging was conducted on the selected location of the dentin surface. The peak intensity and width at 1/e² were recorded in each of the six areas on the sample and averaged. Each group had a sample size of 10. Knoop hardness number (KHN) measurements and scanning electron microscopy (SEM) observations were also conducted. The data for each group were subjected to a one-way repeated-measures ANOVA and Tukey tests (α= 0.05). The samples were also observed using SEM. RESULTS: The peak signal intensities of SDF and PRG decreased on day 7 and then slightly increased during the experimental period for the one-off application groups and then decreased for frequent-time application groups. Although the width at 1/e² in the untreated specimens decreased over the test period, SDF and PRG for the one-off application groups exhibited an increase in widths on day 7 followed by a slight decrease, whereas it increased for the frequent-time application groups. The average KHN of the dentin samples exhibited the same tendency as the width at 1/e². Closure of the dentin tubules and crystal precipitation were detected on the surface of both SDF and PRG groups. CLINICAL SIGNIFICANCE: S-PRG filler-containing gel might have the ability to prevent dentin demineralization and could be useful for the prevention of hard-to-access lesions. This material achieved remineralization of the demineralized root dentin and had the same remineralization ability as SDF in vitro.

Prevention of acidic attack on tooth enamel surfaces using polishing paste containing ion-releasing filler.

The purpose of this study was to investigate the ability of polishing paste containing surface pre-reacted glass-ionomer (S-PRG) filler to prevent acidic attack on tooth enamel surfaces. Resin composites were filled in the standardized cavities and finished with silicon carbide paper. These specimens were divided into three groups: the unpolished "control" group, the "PRG" group polished with S-PRG paste, and the "DDP" group polished with diamond-containing polishing paste. Following polishing, the specimens were immersed in a lactic acid buffer solution for 28 days. Optical coherence tomography (OCT) signals were measured to obtain the signal intensity and width at 1/e2 at selected locations on the enamel surface adjacent to the restoration. Although signal intensity significantly increased in all groups, widths at 1/e2 did not change significantly in the PRG group. For both the control and DDP groups, signal intensity and width at 1/e2 increased and decreased over time, respectively.

Ultrasonic measurement of dentin remineralization effects of dentifrices and silver diamine fluoride.

OBJECTIVE: This study investigated the dentin remineralization effect of the application of a functionalized tri-calcium phosphate (fTCP) dentifrice and a silver diamine fluoride (SDF) solution. MATERIAL AND METHODS: The materials used were: a fluoride-containing dentifrice with fTCP (fTCP＋), a fluoride-containing dentifrice without fTCP (fTCP-) and a 38% SDF solution. Following treatment, the dentin slabs were immersed in a 0.1-M lactic acid buffer solution and then placed in artificial saliva. This procedure was repeated three times daily for 28 days. The propagation time of longitudinal ultrasonic velocities (UV) and the Knoop hardness (KH) of the samples were measured. The samples were also observed using scanning electron microscopy. RESULTS: The SDF and fTCP＋ groups showed higher UV than the fTCP - group regardless of the application method. The F-SDF group at 28 days showed significantly higher UV (4121 ± 102 m/s) than the F-fTCP + group (3731 ± 65 m/s) (p < .05). The F-SDF group at 28 days showed significantly higher KH (47.4 ± 2.2) than the F-fTCP＋ group (43.3 ± 1.0) and the F-fTCP - group (42.9 ± 2.1) (p < .05). Closure of the dentinal tubules and crystal precipitation was detected on the surface of the fTCP＋ group to a greater extent than the fTCP - group. CONCLUSIONS: The fTCP-containing dentifrice and SDF solution effectively enhanced bovine dentin remineralization.

Evaluation of structural coloration of experimental flowable resin composites.

OBJECTIVE: To examine the effect of filler contentTo examine the effect of filler content on structural coloration of experimental flowable resin composites. OVERVIEW: Experimental composites containing spherical fillers and different filler contents (30, 40, 50, 60 and 70 wt%), a structural colored resin composite (Omnichroma), and a nanohybrid flowable resin composite (Gracefil LoFlo) were used. The optical characteristics of the specimens were measured on standard black and white backgrounds using a spectrophotometer under CIE D65 illuminant and the L*a*b* values were determined. The color matching abilities to artificial teeth were evaluated using the ΔE*ab and ΔE00 color difference formulas. One-way analysis of variance and Tukey's post hoc test were used. The spectral reflectance of experimental composites showed different trends in different backgrounds, plate thickness, and filler contents. In particular, higher spectral reflectance was observed on the white background at wavelengths ranging from 450 to 700 nm in both 1.5 and 3.0 mm plates when compared to the black background. The percent reflectivity tended to decrease with a decrease of the filler contents. The color matching abilities of the experimental composites improved with the increase in the filler contents. CONCLUSIONS: Structural coloration of the flowable resin composites were affected by the filler contents. CLINICAL SIGNIFICANCE: Clinical Significance: Higher filler contents might be needed to achieve the optimal color properties of structural colored flowable resin composites, thereby improving the restoration esthetics.

Influence of surface treatment on bonding of resin luting cement to CAD/CAM composite blocks.

The aim of this study was to determine the influence of different surface treatments of CAD/CAM composite blocks on bonding effectiveness of resin cements, based on the shear bond strength test and the surface science examination. Specimens were fabricated from two types of CAD/CAM composite blocks (Cerasmart and VITA Enamic), and the specimen surfaces were alumina sandblasted. Specimen surfaces were treated with i) silane, ii) primer, and iii) silane+primer, then two types of cements (Block HC Cem and Super Bond) were bonded. After 24 h storage, bond strengths were measured. Surface free energy measurements were performed of the treated CAD/CAM composite blocks surfaces. The groups ii) and iii) showed significantly higher bond strengths than the group i), apart from VITA Enamic with Block HC Cem. Although the total surface free energy showed different trends in different surface treatments, a similar trend was found in both CAD/CAM composite blocks.

Ultrasonic measurement of remaining dentin thickness using a pencil-type transducer.

PURPOSE: To evaluate the ability of a pencil-type transducer connected to a pulser-receiver to measure remaining dentin thickness (RDT). METHODS: A total of 24 freshly extracted bovine incisors were used to prepare dentin disks with certain thicknesses (0.5, 1.0, 1.5 and 2.0 mm). The thicknesses of the specimens were measured with an ultrasonic technique using a pencil-type transducer, and the data obtained were compared with the direct measurement obtained using a micrometer. The Bland-Altman comparison method and paired t-test were performed at a 0.05 significance level. RESULTS: The agreement between different measurement methods was analyzed to evaluate the inter-methodology variation. The Bland-Altman comparison method revealed a mean difference of 0.0098 ± 0.724 mm between the ultrasonic technique and the direct measurement, with the 95% Bland-Altman limits of agreement ranging from 0.1322 to 0.1517 mm. CLINICAL SIGNIFICANCE: Ultrasonic measurement using the pencil-type transducer may be a promising method to evaluate remaining dentin thickness.

Effect of a coating material containing surface reaction-type pre-reacted glass-ionomer filler on prevention of primary enamel demineralization detected by optical coherence tomography.

We used optical coherence tomography to examine the effect of a coating material containing surface reaction-type pre-reacted glass-ionomer (S-PRG) filler on primary enamel demineralization in 18 extracted human primary teeth. The pulp was removed, and each tooth was ultrasonically cleaned with distilled water. Six teeth were treated with 0.1-M lactic acid buffer solution (De group). In the second group (n = 6), a thin film of coating material was applied before demineralization (PRG group). A third group (Control group; n = 6) was maintained in artificial saliva. Using optical coherence tomography, we measured peak signal intensity (dB) and width at 1/e2 (µm) at predetermined locations on the enamel surface and calculated integrated values. All data were analyzed with ANOVA and the Tukey-Kramer test (α = 0.05). Although changes in integrated values differed between groups, there was a small but significant increase in the Control group and a small but significant decrease in the De group. In the PRG group, integrated values were significantly higher at 7 days after the start of the experiment and significantly increased thereafter. Our findings indicate that a coating material containing S-PRG fillers may prevent primary enamel demineralization.

Effect of acid erosion on enamel bond strength of self-etch adhesives and sonic velocity measurement of enamel.

The purpose of this study was to investigate the effect of acid erosion on the bonding performance of universal adhesives. Freshly extracted bovine teeth were cut into enamel slabs and assigned to either the Er or the control group. Specimens in the Er group were immersed in citric acid solution (pH 2.1) twice a day and stored in artificial saliva, while control specimens were simply stored in artificial saliva. Differences in the mean values between the control and Er groups were greater than expected, despite accounting for the effect of differences in the adhesive systems (p=0.016). The Er group mainly exhibited cohesive failure in the enamel, while adhesive failure was more frequent in the control group. The sonic velocity was found to decrease over time in the acid attacked specimens. The results indicated that bond strengths of universal adhesive tested increased in eroded enamel.

Effect of light irradiation and primer application on polymerization of selfadhesive resin cements monitored by ultrasonic velocity.

In this study, we investigated the effect of light irradiation and primer/adhesive application on the polymerization reaction and elastic modulus (E) of self-adhesive resin cement (SAC) through ultrasonic velocity (V) measurements. The V values of longitudinal and shear waves were determined based on the transit time through the specimens and specimen thicknesses, and were used to calculate the E values. Analysis of variance and Tukey tests revealed that V increased rapidly, reaching a plateau at 2,700-2,900 m/s, when the SACs were light-irradiated. However, the increasing rate of V was retarded for the non-irradiated SACs. In addition, when the primer/adhesive was applied, higher E values were obtained after 24 h. Finally, the polymerization behavior of the SACs was affected by light irradiation and primer application, and the use of prime/adhesive might improve mechanical properties. In clinical situations, use of primer/adhesive is recommended for getting proper adhesion.

Influence of air-powder polishing on bond strength and surface-free energy of universal adhesive systems.

The influences of air-powder polishing with glycine or sodium bicarbonate powders on shear bond strengths (SBS) and surface-free energies of universal adhesives were examined. Scotchbond Universal Adhesive (SU, 3M ESPE), G-Premio Bond (GP, GC), Adhese Universal (AU, Ivoclar Vivadent), and All-Bond Universal (AB, Bisco) were used in this study. Bovine dentin surfaces were air polished with glycine or sodium bicarbonate powders prior to the bonding procedure, and resin pastes were bonded to the dentin surface using universal adhesives. SBSs were determined after 24-h storage in distilled water at 37°C. Surface-free energy was then determined by measuring contact angles using three test liquids on dentin surfaces. Significantly lower SBSs were observed for dentin that was air-powder polished and surface-free energies were concomitantly lowered. This study indicated that air-powder polishing influences SBSs and surface-free energies. However, glycine powder produced smaller changes in these surface parameters than sodium bicarbonate.

Enamel remineralization effect of a dentifrice containing calcium sodium phosphosilicate: an optical coherence tomography observation.

OBJECTIVE: The purpose of this study was to examine the effects of a dentifrice containing 5% calcium sodium phosphosilicate (CSP) on the remineralization of the enamel using optical coherence tomography (OCT). MATERIALS AND METHODS: Bovine incisors were sliced and shaped in a rectangular form. One group of five specimens was treated with undersaturated 0.1 M lactic acid buffer solution (pH 4.75) for 10 min and then placed in artificial saliva (pH 7.0) (De group). Other specimens were stored in solutions of toothpaste containing CSP for 10 min, followed by 10-min immersion in the lactic acid buffer solution twice a day before storage in artificial saliva (CSP group). An additional group was stored in only artificial saliva (control group). OCT imaging on the selected location of the enamel surface was performed. The peak intensity and width at 1/e2 were recorded in each of the six areas on the sample and averaged, and the sample size of each group was six. The integrated value in units (dB × µm) was calculated in the area of peak intensity. The data for each group was subjected to one-way repeated-measures ANOVA and Tukey HSD tests (α = 0.05). RESULTS: The changes in integrated values of each group were different. A slight but significant increase in the integrated value was observed in the control group, whereas a slight but significant decrease in the value was observed the De group. Integrated values increased in the CSP group. CONCLUSIONS: Remineralization occurred upon immersion in the toothpaste containing CSP.

Ultrasonic monitoring of the setting of silicone elastomeric impression materials.

This study used an ultrasonic measurement device to monitor the setting behavior of silicone elastomeric impression materials, and the influence of temperature on setting behavior was determined. The ultrasonic device consisted of a pulser-receiver, transducers, and an oscilloscope. The two-way transit time through the mixing material was divided by two to account for the down-and-back travel path; then it was multiplied by the sonic velocity. Analysis of variance and the Tukey honest significant difference test were used. In the early stages of the setting process, most of the ultrasonic energy was absorbed by the elastomers and the second echoes were relatively weak. As the elastomers hardened, the sonic velocities increased until they plateaued. The changes in sonic velocities varied among the elastomers tested, and were affected by temperature conditions. The ultrasonic method used in this study has considerable potential for determining the setting processes of elastomeric impression materials.

Ultrasonic assessment of the effects of self-assembling peptide scaffolds on preventing enamel demineralization.

OBJECTIVES: This study evaluates the effect of self-assembling peptide P11-4 (Curodont Repair, CDR) on bovine enamel remineralization by measuring changes in ultrasonic propagation velocity. METHODS: Six specimens per group were prepared by sectioning bovine teeth into enamel blocks. These blocks were then immersed in lactic acid buffer solution (pH = 4.75) for 10 min twice a day and stored in artificial saliva. Other specimens were first treated with CDR, followed by a 10-min immersion in the lactic acid buffer solution twice a day, before storage in artificial saliva. The propagation time of longitudinal ultrasonic waves was measured using a pulser/receiver. Six specimens were used for each treatment protocol. The obtained data were statistically analyzed using ANOVA followed by Tukey's honestly significant difference tests (α = 0.05). Specimens were observed using laser scanning microscopy and scanning electron microscopy. RESULTS: Sonic velocity was found to decrease with time for specimens stored in the demineralizing solution. On the other hand, increases in sonic velocity were found for specimens treated with CDR. These specimens also exhibited signs of mineral deposition. CONCLUSIONS: By measuring the ultrasonic propagation velocity, it can be concluded that CDR application has an ability to promote bovine enamel remineralization.

Ultrasonic measurement of the effects of light irradiation and presence of water on the polymerization of self-adhesive resin cement.

Self-adhesive resin cements are useful in restorations because they reduce the number of clinical steps involved in the restoration process. This study evaluated, using ultrasonic measurements, the influence of light irradiation and the presence of water on the polymerization behavior and elastic modulus of a self-adhesive resin cement. A self-adhesive resin cement (RelyX Unicem 2 Automix) or a resin cement (RelyX ARC) was inserted into a transparent mold on a sample stage, and the presence of water and effect of light-irradiation were evaluated. The transit time of a sonic wave through the cement disk was divided by the specimen thickness to obtain the sonic velocity, and longitudinal and shear waves were used to determine the elastic modulus. When the resin cements were light-irradiated, the sonic velocity rapidly increased and plateaued at 2,500-2,700 m s-1 . When the cements were not irradiated, the rates of increase in the sonic velocity were reduced. When water was applied to the sample stage, the sonic velocity was reduced. The elastic modulus values of the specimens ranged from 9.9 to 15.9 GPa after 24 h. The polymerization behavior of self-adhesive resin cements is affected by the polymerization mode and the presence of water.

Three-year clinical evaluation of posterior composite restorations placed with a single-step self-etch adhesive.

In this clinical study, we evaluated the 3-year clinical performance of a resin composite containing a surface-prereacted glass ionomer (S-PRG) filler (Beautifil II; Shofu Inc., Kyoto, Japan) placed with a single-step self-etch adhesive (BeautiBond; Shofu Inc.) in posterior restorations. Using modified US Public Health Service criteria, two experienced investigators performed clinical evaluations at the baseline, 6 months, 18 months, and 3 years. Color match, marginal adaptation, anatomical form, surface roughness, marginal discoloration, postoperative sensitivity, and secondary caries were evaluated. After 3 years, 26 patients attended the recall and 31 restorations were evaluated. No postoperative sensitivity or secondary caries was observed at any time point, and no restorations failed during the follow-up period. However, surface roughness, marginal adaptation, and marginal discoloration showed deterioration after 3 years. In conclusion, although some clinical changes were observed, resin composite containing S-PRG filler placed with self-etch adhesive exhibited acceptable clinical behavior in posterior restorations.

Evaluation of the effects of fluoride-releasing varnish on dentin demineralization using optical coherence tomography.

Effects of a fluoride-releasing varnish containing surface reaction-type prereacted glass ionomer (S-PRG) filler on dentin demineralization were examined using optical coherence tomography. Bovine incisors that were sliced and treated with undersaturated 0.1 M lactic acid buffer solution (DE group). A thin film of varnish-containing S-PRG filler was applied before demineralization (PRG group). Control was maintained in artificial saliva. Using optical coherence tomography of selected locations on the dentin surface, peak intensity (dB) and width (µm) at 1/e(2) were obtained and integrated values calculated. Although alterations in integrated values were different in each group, there was a slight but not significant increase in those for the control group and a slight but significant increase for the De group. For the PRG group, integrated values were doubled seven days after experiment initiation, followed by a significant increase. Fluoride-releasing varnish containing S-PRG fillers prevented dentin demineralization as detected by optical coherence tomography.